Parkside PWSA 18 A1 Manual de usuario Pagina 15
- Pagina / 78
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
15
GB IE CY
such as described below.
a) Hold the electric tool very
rmly and bring your body and your
arm into a position in which you can
resist the kickback force. Always use
the supplemental handle if available to
give you the best control over kickback
force or reaction time during accel-
eration. The operator can master the
kickback and reaction force through
suitable precautions.
b) Never bring your hands near a
rotating attachment tool. The at-
tachment tool can run over your hand
in the kickback.
c) Keep your body away from the
area in which the electric tool
would move during a kickback.
The kickback drives the electric tool in
the counter-direction to the rotation of
the grinding disc at the blocked spot.
d) Work particularly cautiously in
corner areas or where there are
sharp corners etc. Prevent the at-
tachment tools from recoiling from the
workpiece and jamming. The rotating
attachment tool tends to jam when near
corners, sharp edges or when it recoils
from such. This causes a loss of control
or kickback.
e) Do not use chain or toothed
saw blades. Such attachment tools
frequently cause a kickback or loss of
control over the electric tool.
Special safety instructions for
grinding and cutting
a) Use only grinders which have
been approved for your electric
tool and the protective hood in-
tended for these grinders. Grind-
ers which are not intended for the elec-
tric tool may not be sufciently shielded
and are unsafe.
b) Depressed centre grinding
wheels must be pre-mounted in
such a way that their grinding
surface does not protrude over
the level of the edge of the pro-
tective cover. An incorrectly mounted
grinding wheel which protrudes beyond
the level of the edge of the protective
cover cannot be adequately shielded.
c) The protective hood must be
securely attached to the elec-
tric tool and adjusted so that
the greatest level of safety is
reached, i.e., the smallest possible
amount of the grinder is exposed to the
operator. The protective hood should
protect the operator from broken bits
and accidental contact with the grinder.
d) Grinders may only be used for
the recommended attachment
options. For example: Never grind
with the side surface of a cutting disc.
Cutting discs are for cutting material
using the edge of the disc. Pushing
sideways on these grinders can break
them.
e) Always use undamaged clamp-
ing anges of the correct size
and shape for the grinding disc
you selected. Suitable anges sup-
port the grinding disc and thus reduce
the danger of the grinding disc break-
ing. Flanges for cutting discs can be
distinguished from anges for other
grinding discs.
f) Do not use worn grinding discs
for larger electric tools. Grinding
discs for larger electric tools are not
set up for the higher rotation speeds of
- IAN 104454 1
- Introduction 4
- Intended purpose 4
- General description 5
- Technical data 5
- Notes on safety 6
- GB IE CY 10
- Charging the battery 17
- Practical tips 18
- Assembly 18
- Operation 19
- Cleaning and servicing 21
- Disposal and protection 21
- Replacement parts/Accessories 22
- Troubleshooting 23
- Guarantee 24
- Repair Service 25
- Service-Center 25
- Importer 25
- Περιεχόμενα 26
- Σκοπός χρήσης 26
- Γενική περιγραφή 27
- Τεχνικά στοιχεία 27
- R (L 28
- Υποδείξεις ασφάλειας 29
- Γενικές υποδείξεις ασφαλείας 30
- Περαιτέρω υποδείξεις 36
- Ανάκρουση 38
- Ειδικές υποδείξεις ασφάλειας 38
- Υποδείξεις εργασίας 42
- Συναρμολόγηση 42
- Καθαρισμός και 45
- Συντήρηση 45
- Αποθήκευση 45
- Απόσυρση/προστασία του 45
- 46
- 47
- Εισαγωγέας 48
- Ανταλλακτικά / Αξεσουάρ 49
- Ανίχνευση βλαβών 50
- Einleitung 51
- Bestimmungsgemäße 51
- Verwendung 51
- Allgemeine 52
- Beschreibung 52
- Technische Daten 52
- DE AT CH 53
- Sicherheitshinweise 54
- Ladevorgang 65
- Arbeitshinweise 67
- Bedienung 68
- Reinigung und Wartung 69
- Lagerung 70
- Entsorgung/ 70
- Umweltschutz 70
- Garantie 71
- Reparatur-Service 72
- Importeur 72
- Ersatzteile/Zubehör 73
- Fehlersuche 74
- Μετάφραση της πρωτότυπης 76
- Δήλωσης συμμόρφωσης CE 76
- Original 77
- EG Konformitätserklärung 77
Relacionado con productos y manuales para Rectificadoras Parkside PWSA 18 A1
Rectificadoras Parkside PWSA 18 A1 Manual de usuario
(78 paginas)
(78 paginas)
Rectificadoras Parkside PWSA 18 A1 Manual de usuario
(170 paginas)
(170 paginas)
Rectificadoras Parkside PDS 290 A1 Manual de usuario
(29 paginas)
(29 paginas)
Rectificadoras Parkside PDS 290 A1 Manual de usuario
(47 paginas)
(47 paginas)
Rectificadoras Parkside PWP 90 B2 Manual de usuario
(50 paginas)
(50 paginas)
Rectificadoras Parkside PWP 90 B2 Manual de usuario
(58 paginas)
(58 paginas)
Rectificadoras Parkside PEH 30 A1 Manual de usuario
(34 paginas)
(34 paginas)
Rectificadoras Parkside PEH 30 A1 Manual de usuario
(35 paginas)
(35 paginas)
Rectificadoras Parkside PWP 90 B2 Manual de usuario
(70 paginas)
(70 paginas)
Rectificadoras Parkside PDOS 200 B2 Manual de usuario
(104 paginas)
(104 paginas)
Poulan 183981 manuales
Manuales del propietario y guías del usuario para Máquinas De Jardín Poulan 183981.
Ofrecemos 1 manuales en pdf Poulan 183981 para descargar gratis por tipos de documentos: Manual de usuario
Comentarios a estos manuales